Almost everyone has their personal thinking involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a tub isn't exactly brain surgery, however it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is easily obtainable, the project can move speedily; if you need to open up a wall surface to remove the old bathtub and also position the new tub, the job is a lot harder. In either case, the job is within a house handyman's abilities, although you will certainly require a helper to move out the old tub and set in the new one. Make sure you have qualified yourself for the job as well as are comfortable trying it. Rather than working with a specialist to take control of a halfway-completed job, it is much better to take into consideration utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly aid you set up a new bath tub in your washroom if you have actually already acquired a brand-new tub and also do not need to transform the plan of your previous supply of water pipelines.
Your tools and also material list must comprise the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you must do is separate the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing faucets can be fairly problematic due to the restricted gain access to that is usually the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the staying water that will certainly come from the pipes. Once the supply pipes have actually been gotten rid of, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from turning during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular faucet ports. The former type should be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bath tub
Utilizing the two wood boards under its feet, place the bath tub in the needed position. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 small factors.
The next objective is to make certain that the tub is leveled all round. This can be attained by checking the level and also adjusting the feet on the tub till the spirit level checks out degree.
To mount taps, fit the bottom of the furthest adaptable faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Switch on the water system as well as examine all joints and also brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally examine the overflow electrical outlet and also the typical electrical outlet for leaks.
Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling as well as securing around the tub needs to wait up until the bathtub has been used at the very least when as this will certainly resolve it right into its last position.
Preparing for the Installation
First of all, the supporting framework supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make sure that if the faucet includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath ought to currently be ready to be fitted in its last placement.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a stiff seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, resulting in difficulties with dampness and possible leaks to the ceiling below.
You can choose from a range of coloured sealants to assimilate your fixtures and installations. They are sold in tubes as well as cartridges, and also are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water prior to securing, to permit the activity experienced when the bathtub is in use. The sealant can crack rather very early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently offered on the market. It is recommended to fit the tiles utilizing water-resistant or water-proof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that blog posting about How to Install a Bathtub Yourself while looking around the search engines. Do you know about somebody else who is fascinated about the niche? Take a moment to promote it. Kudos for your time. Kindly come visit our blog back soon.
Rely on our emergency expertise.